摘要：污水處理工程電腦測控系統主要研究污水處理工程中，如何利用電腦測控技術，對水位、溫度、PH值、流量等檢測量進行數據采集，上位機通過PC測控軟件Obtain_AU實現各站數據交換和顯示，并通過控制單元控制電機實現進出水控制。該系統采用分布式結構，各下位機通過有線通信模塊與上位機進行通信，其中有線通信采用RS_485或CAN總線標準，無線通信采用具有RS_232接口的無線數傳模塊或GSM/GPRS模塊實現。該系統最主要的特點一是采用了嵌入式系統（嵌入式軟PLC）代替PLC、工控板等傳統的工業控制設備；二是采PC測控軟件Obtain_AU代替普通的組態軟件。本文主要介紹該系統的功能、軟硬件設計方案以及軟件各個模塊的流程圖，簡要地分析了該系統設計的要點、難點及其實現方法。

關鍵詞：污水處理；電腦測控；ARM；FPGA 

Abstract: Sewage Treatment disposal project of computer measuring and control technology system main sewage treatment works, the use of computer monitoring and control technologies, collecting data such as water level, temperature, PH value, flux and so on, master station exchange data with each station through Obtain_AU software of PC, and control MOTO with control unit.This system uses points of distributed. Each station connected to master station by wire communication module. and wire communication using the main line standard of RS_485 or CAN. And then wireless communication realize by including RS_232 interface operate module or GSM/GPRS module.

　　 The main characteristic of this system is that embedded system replaces the tradition industry control equipments of PLC and industry control board and the other is that uses measuring and control software obtain AU which owning the intellectual property rights by Mr liao who invented to replace normal configuration software.

　　 In this paper the system’s features and design aspects of programs introduced and flow sheet of each software module. Sample analysis the main point the difficulty and the realization of the system . 

Keywords: Sewage disposal；Computer Measuring & Control  ；ARM；FPGA

　　　隨著計算機技術和儀表自動化的發展，小型的水處理池、泵站及一些小的廠站系統實現無人值守或少人值守己經成為必然趨勢。這就要求具有經濟、實用的監控系統。監控系統是指將廠站中的實時數據通過變送器變?yōu)殡娦盘枺谕ㄟ^板卡或傳感器采集，經過數字處理，轉變?yōu)橛嬎銠C可以處理的數字信號，在上位機處理后實時的顯示出來，或通過這些數據得到相應的結論去控制過程對象的一種計算機控制系統。它可以完成實時遠距離數據的實時顯示，監控管理，越限報警，等功能。